Licensed & Insured
Local & Trusted
Free Estimates

Drip Edge on a Roof: What It Is and If Yours Needs One

A drip edge on a roof is a strip of metal flashing along the eaves and rakes that directs water off the roof edge and away from the fascia and decking. The 2018 International Residential Code, which Wichita and Sedgwick County use through MABCD, calls for one on shingle roofs, and shingle makers recommend it on every roof. If your roof has none, a replacement is the easiest time to add it.

This guide covers what the code says about a drip edge on a roof, the profiles, the correct order with underlayment, what it costs and how insurance treats it.

2018 IRC rules for a drip edge on a roof
The four installation rules for a drip edge on a roof in the 2018 International Residential Code.

What does a drip edge on a roof actually do?

ARMA, the Asphalt Roofing Manufacturers Association, says drip edges “provide efficient water shedding at a shingled roof’s eave, gable, and rake.” They also help limit rot in the wood under the shingles. Without one, the roof edge has no metal path to carry runoff clear of the wood.

InspectApedia makes the same point about drip edge mistakes: water leaving the roof edge “wants to run down building fascias, soffits, and walls” when the metal is missing or the wrong shape. Check for a missing drip edge on a roof when you see rotted fascia or algae stains under the gutter. See gutters in Wichita for how the pieces fit together.

Does code require a drip edge on a roof in Wichita?

For shingle roofs, yes under the base 2018 IRC. MABCD enforces the 2018 IRC with local amendments, so confirm the current local text at 316-660-1840. Section R905.2.8.5, as published by the City of Pacific, Missouri, reads: “A drip edge shall be provided at eaves and rake edges of shingle roofs.”

Codes differ by state. South Carolina’s version says a drip edge is required only “where required by the manufacturer.” Do not assume another state’s amendment applies here. Most replacements in Wichita need a roofing permit and a final inspection, and our guide to the Wichita roof replacement permit explains the steps.

What are the installation rules for a drip edge on a roof?

The 2018 IRC text, as quoted by the same city document, sets these minimums:

  • Overlap. Adjacent segments overlap “not less than 2 inches.”
  • Extension. The metal extends “not less than 1/4 inch” below the roof sheathing and back onto the roof deck at least 2 inches.
  • Fastening. It is mechanically fastened to the deck at not more than 12 inches on center.
  • Order. “Underlayment shall be installed over the drip edge along eaves and under the drip edge along rake edges.”

The last rule is the one most often reversed. Owens Corning states the same order in its Technical Bulletin TB-04 of September 20, 2017: drip edge goes below the underlayment at the eaves and on top of it at the rakes.

LocationDrip edge goes
EavesUnder the underlayment
RakesOver the underlayment

ARMA adds an exception. With self-adhering underlayment at the eave, some manufacturers or local codes allow the drip edge over the underlayment. Follow the shingle maker’s instructions for the product on the roof.

What do shingle manufacturers require?

Manufacturers set their own rules, and they can be stricter than code. GAF’s technical bulletin TAB-R-141 says it “strongly recommends” drip edge at the rakes and eaves on all GAF shingle roofs, and requires it at eaves when a Silver or Golden Pledge warranty is sought. It also states that “L” metal is not acceptable as a drip edge.

Owens Corning recommends installing drip edge on all roofs covered with asphalt shingles and says shingles should overhang its outer edge by 1/4 to 3/4 inch. GAF limits the shingle overhang past the drip edge to 3/4 inch. Because GAF ties a drip edge on a roof to its top warranties, check the paperwork before agreeing to skip it.

Cost of a drip edge on a roof by profile
Published cost per linear foot for three drip edge profiles.

Which drip edge profile is right for your roof?

This Old House, citing Angi cost data, describes three common shapes. Profile names vary by supplier, so confirm the shape with the installer.

ProfileShape and useCost per linear foot
Type C (L-style)90-degree bend, suited to low-profile roofs$0.30 to $1
Type D (T-style)Extends farther over the gutter; ARMA recommends it for most residential roofs$1 to $1.50
Type FLonger leading edge, easier to add over existing shingles$0.30 to $1

A gutter apron is not technically a drip edge, but it does a similar job and reaches farther into the gutter. ARMA says that with T- or D-shaped drip edge, rake shingles can be trimmed flush and eave shingles may extend up to 3/4 inch. Check the profile guide for materials such as aluminum, galvanized steel and copper.

Can you add a drip edge on a roof that already has shingles?

Yes, but it takes more work. This Old House says Type F is easier to secure over existing shingles. Angi recommends hiring a professional for installation on an existing roof. Adding the metal during a replacement is simpler because the deck is bare.

Check where the roof edge meets the gutter. A gutter hung above the drip edge sends water behind it, a problem InspectApedia shows with algae stains under the gutter. If you are reroofing, see roof replacement in Wichita and our roof flashing guide for the other edge details.

How much does a drip edge cost?

Angi says a drip edge “costs $1 to $3 per linear foot on average, which comes out to about $150 to $1,000 for most homes.” HomeAdvisor, updated June 17, 2026, lists $1 to $2 per linear foot. Material matters: copper costs far more than aluminum or galvanized steel. These are third-party figures, not bids.

Will insurance pay to add a drip edge during a claim?

Only if the policy covers code upgrades. Progressive explains that “ordinance or law coverage” can help pay to bring a home up to code after a covered loss, usually as a percentage such as 10% or 25% of dwelling coverage. It also says a standard homeowners policy typically will not pay for code upgrades.

Ask your agent if your policy includes this coverage before a storm. Read roof insurance claims and ACV vs RCV roof coverage for the wider claim picture.

Drip edge questions from Wichita homeowners

Is a drip edge on a roof required?

The 2018 IRC requires it at eaves and rakes of shingle roofs, but states and cities amend the code. GAF and Owens Corning both strongly recommend it. In Wichita, ask MABCD for the current local text before you accept a bid without one.

What happens if a roof has no drip edge?

Water can run down the fascia, soffit and wall instead of dropping clear of them, and ARMA says drip edge helps limit rot in the wood. It may also weaken warranty protection at the eaves, depending on the shingle maker.

Does drip edge go over or under underlayment?

At the eaves, the 2018 IRC puts the underlayment over the drip edge. At the rakes, the drip edge goes on top of the underlayment. Self-adhering underlayment can be an exception with some manufacturers.

Can drip edge be added to an old roof?

Yes. Type F is made for adding a drip edge on a roof that is already shingled, and Angi recommends a professional for existing roofs. Adding it during a replacement is simpler.

Get a drip edge on a roof done right in Wichita

Equity Builders is a Wichita roofing and exterior contractor at 442 S. Ellis St., founded in 1985, and offers a lifetime workmanship warranty with no payment until the job is done. Ask for the drip edge profile, material and underlayment order in writing. Call (316) 425-0455 or request a free estimate.

Sources

  • City of Pacific, Missouri, Roof Code (2018 IRC Section R905.2.8.5 text)
  • Cornell Legal Information Institute, S.C. Code Regs. 8-1228
  • GAF, Technical Bulletin TAB-R-141, Drip Edges and Shingles
  • Owens Corning, Technical Bulletin TB-04, Drip Edge Installation, September 20, 2017
  • Asphalt Roofing Manufacturers Association, Installation of Drip Edge at Eaves and Rakes, May 6, 2025
  • Angi, roof drip edge, and HomeAdvisor, fascia and soffit cost, updated June 17, 2026
  • Progressive, ordinance or law coverage, updated July 3, 2025
  • Sedgwick County MABCD, permits page
  • InspectApedia, Roof Drip Edge Flashing Mistakes

Last updated October 24, 2026. Codes and manufacturer rules change. Confirm current requirements with MABCD and your shingle manufacturer.

Facebook
Twitter
LinkedIn
Call Now for a Free Estimate(316) 425-0455